Kodi 19.4 dietpi 8.11.2 cpu temp bug

[Thundervarela]

Kodi 19.4 dietpi 8.11.2 cpu temp bug , missing cpu temp disable i can check it on the commandline but not on the kodi interface like this : https://imageshack.com/i/pnnyCkohj

[MichaIng]

I suppose it's an RPi. This is a limitation of Kodi then, not supporting the RPi sysfs entries. Or it uses the sensors package:

apt install lm-sensors

It this does not help we could report this to the RPi maintainer of the Kodi package. They do HW acceleration patches and such with the RPi build, so probably might add support for CPU temps as well.

[Thundervarela]

That's the output of that command

[Thundervarela]

i would report it if would know who is the RPi maintainer of the Kodi package and how to reacht him ...

[MichaIng]

Ah sorry, this is the correct package name:

apt install lm-sensors

[Thundervarela]

well i run the command apt install lm-sensors and reboot and it doesn't fix it . Already reported to xbmc/xbmc#22240

[MichaIng]

This is the upstream repository, not the RPi specific one. Here it would be suited best: https://forums.raspberrypi.com/viewtopic.php?t=323303

And note that upstream developers usually require a lot more information to even start recognising a report, hardware, exact build, where it comes from, OS version (DietPi is irrelevant, it's Debian Bullseye, while Kodi packages come from RPi package repository) etc. But I'm quite sure they refer to downstream package maintainers back anyway, as long as you did not verify with a fresh upstream source build.

[Thundervarela]

I think i found it

[EdWaQ]

Can someone explain how I upgrade my kodi from 18.9 to 19+

[MichaIng]

That is always a good idea 👍.

[EdWaQ]

Upgrade don't work, any error from buster to bullseye. I set a new clean dietpi on das card well done work fine.

[MichaIng]

Upgrade don't work, any error from buster to bullseye.

Seems to late now, but if you told us the error message, we surely would have been able to solve it 😉. But a clean install is anyway recommended, just possibly more work to setup everything again.

[EdWaQ]

libc6-dev : Broken: libgcc-8-dev (< 8.4.0-2~) but 8.3.0-6+rpi1 should be installed this was the error after I use this code

# ProFTPD
[[ -f '/etc/proftpd/proftpd.conf' ]] && ! grep -q 'IfModule mod_ident.c' /etc/proftpd/proftpd.conf && sed -i '/IdentLookups/c\<IfModule mod_ident.c>\nIdentLookups off\n</IfModule>' /etc/proftpd/proftpd.conf

# Legacy network interface names
# - RPi
(( $G_HW_MODEL < 10 )) && ! grep -q 'net.ifnames=0' /boot/cmdline.txt && sed -i '/root=/s/$/ net.ifnames=0/' /boot/cmdline.txt
# - Odroid XU4
(( $G_HW_MODEL == 11 )) && ! grep -q 'net.ifnames=0' /boot/boot.ini && sed -i '/bootrootfs/s/"$/ net.ifnames=0"/' /boot/boot.ini
# - Armbian
[[ -f '/etc/armbianEnv.txt' ]] && ! grep -q 'net.ifnames=0' /etc/armbianEnv.txt && G_CONFIG_INJECT 'extraargs=' 'extraargs="net.ifnames=0"' /boot/armbianEnv.txt

[MichaIng]

This error is not related to the executed code but to the the apt full-upgrade only. The libgcc-8-dev package is a Buster package, and a development package anyway (not needed to "run" software, just to "build" software). So you can safely purge it:

apt autopurge libgcc-8-dev