telex.json

# Configuration examples for piTelex
# 2023-03-15
# requirements: commentjson, argparse (additional requirements per section are listed there)
#
# This file can be used as a starting point for piTelex installations using the default hardware configuration.
# Screen and log module should be enabled always for testing and debugging purposes.
# Archive module, if enabled, saves a prettyprint transcript of each connection.
#
# enable the TTY module(s) that correspond to your TTY type.
# Disable ("enable": false,) or optionally delete unused modules or entries.
#
# For detailed configuration infos see the wiki pages.
#
# Additional modules are described in the telex_Example_XXX.json files
#
{
  "devices": {
    # screen output and kwyboard input (for debugging)
    "screen": {
      "type": "screen",
      "enable": true,
      "show_BuZi": true,
      "show_ctrl": true,
      "show_info": false,
      "show_capital": false
    },

    ###########################################################################

    # Module type "RPiTTY"
    # requirements: pigpio (deamon and lib)
    # TW39 or V10 teletype with FSG over GPIO pins of Raspberry Pi
    
    # standard, minimal example for a teletype with FSG
    "RPiTTY_typical": {
      "type": "RPiTTY",
      "enable": false,
      "mode": "TW39",
      "pin_txd": 17,
      "pin_rxd": 27,
      "pin_relay": 22,
      "pin_number_switch": 6,      # classic layput: 6   new layout: 10
      "baudrate": 50,
      "loopback": true
    },

    ###

    # control the workflow (dialing, idle, typing-mode, text-phrases) with buttons
    # and show status with LEDs
    "RPiCtrl": {
      "type": "RPiCtrl",
      "enable": true,

      # separate number switch - see also module RPiTTY
      "pin_number_switch": 0,

      # user buttons   B1/B2/B3/B4: 8/7/5/6   Pin 40: 21
      "pin_button_1T": 21,         # Single button AT->LT->ST
      "pin_button_AT": 0,          # AT-button to request dialing
      "pin_button_ST": 0,          # ST-button to stop a connection
      "pin_button_LT": 0,          # LT-button to switch to local mode
      "pin_button_PT": 8,          # PT-button to wakeup ffrom sleep mode
      "pin_button_U1": 0,          # user-button 1
      "pin_button_U2": 0,          # user-button 2
      "pin_button_U3": 0,          # user-button 3
      "pin_button_U4": 0,          # user-button 4
      "text_button_U1": "Hello",   # text for user-button 1
      "text_button_U2": "Hello",   # text for user-button 2
      "text_button_U3": "Hello",   # text for user-button 3
      "text_button_U4": "Hello",   # text for user-button 4

      # single LEDs
      "pin_LED_LT": 0,
      "pin_LED_A": 0,
      "pin_LED_WB": 0,
      "pin_LED_WB_A": 0,

      # Duo-LEDs with common cathodes for status info
      "pin_LED_status_R": 23,
      "pin_LED_status_G": 24,

      # power saving
      "pin_power": 0,              # GPIO on SEU-M: 9
      "inv_power": false
    },

    ###########################################################################

    # Module type "i-Telex"

    "i-Telex": {
      "type": "i-Telex",
      "enable": true,
      "port": 2342,
      # WARNING
      # Setting tns-dynip-number to anything except 0 will enable dynamic IP
      # updates with i-Telex TNS (Teilnehmerserver, Subscriber Server).
      #
      # Leave at 0 if you've chosen a static TNS entry!
      # Change to something nonzero if and only if
      # - you've got your number approved by i-Telex administrators, and
      # - you've chosen dynamic IP update and told i-Telex administrators so, and
      # - you've set your TNS pin properly.
      "tns_dynip_number": 0,
      "tns_pin": 12345
    },

    ###########################################################################

    "log": {
      "type": "log",
      "enable": true,
      "filename": "./data.log"
    },

    ###########################################################################

    "archive": {
      "type": "archive",
      "enable": true,
      "path": "./archive/"
    }
  
  },

  ###########################################################################

  "wru_id": "12345 dummy d",
  "wru_replace_always": false,
  "dial_timeout": 0,
  "continue_with_no_printer": false,
  "errorlog_path": "./errorlog/"
}