-
Notifications
You must be signed in to change notification settings - Fork 1
/
hacklab_experimental_superspeed.ini
114 lines (112 loc) · 3.62 KB
/
hacklab_experimental_superspeed.ini
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
[profile]
machine_center_x = 100
machine_center_y = 100
flip_x = False
flip_y = False
flip_z = False
swap_xz = False
swap_yz = False
model_scale = 1.0
model_rotate_base = 0
filament_diameter = 2.98
nozzle_size = 0.40
layer_height = 0.2
wall_thickness = 0.8
solid_layer_thickness = 0.6
fill_density = 3.5
skirt_line_count = 2
skirt_gap = 3.0
print_speed = 123
print_temperature = 220
support = None
enable_raft = False
filament_density = 1.00
retraction_min_travel = 5.0
retraction_speed = 60.0
retraction_amount = 3.0
retraction_extra = 0.0
travel_speed = 170
max_z_speed = 3.0
bottom_layer_speed = 30
cool_min_layer_time = 2
fan_enabled = True
bottom_thickness = 0.3
enable_skin = False
extra_base_wall_thickness = 0.0
cool_min_feedrate = 10
fan_layer = 1
fan_speed = 100
fan_speed_max = 100
raft_margin = 5
raft_base_material_amount = 100
raft_interface_material_amount = 100
support_rate = 50
support_distance = 0.5
infill_type = Grid Hexagonal
solid_top = True
fill_overlap = 15
bridge_speed = 100
sequence = Infill > Perimeter > Loops
force_first_layer_sequence = True
joris = False
retract_on_jumps_only = True
enable_dwindle = True
dwindle_pent_up_volume = 0.7
dwindle_slowdown_volume = 5.0
retraction_enable = True
plugin_config = (lp1
.
hop_on_move = False
gcode_extension = gcode
object_center_x = -1
object_center_y = -1
alternative_center =
add_start_end_gcode = True
model_multiply_x = 1
model_multiply_y = 1
support_dual_extrusion = False
[alterations]
start.gcode = ;Sliced {filename} at: {day} {date} {time}
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
;Print time: {print_time}
;Filament used: {filament_amount}m {filament_weight}g
;Filament cost: {filament_cost}
M92 X79.1359 Y79.1359 Z526.112 E810.0
G21 ;metric values
G90 ;absolute positioning
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G92 X0 Y0 Z0 E0 ;reset software position to front/left/z=0.0
G1 Z15.0 F{max_z_speed} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
;go to the middle of the platform (disabled, as there is no need to go to the center)
;G1 X{machine_center_x} Y{machine_center_y} F{travel_speed}
G1 F{travel_speed}
end.gcode = ;End GCode
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
replace.csv =
support_end.gcode =
nextobject.gcode = ;Move to next object on the platform. clear_z is the minimal z height we need to make sure we do not hit any objects.
G92 E0
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 F{travel_speed} ;move Z up a bit and retract filament even more
G90 ;absolute positioning
G1 Z{clear_z} F{max_z_speed}
G92 E0
G1 X{machine_center_x} Y{machine_center_y} F{travel_speed}
G1 F200 E5
G92 E0
support_start.gcode =
cool_end.gcode =
cool_start.gcode =