v9.02 won't reboot by itself (if it hangs)

[kotylo]

PROBLEM DESCRIPTION

Nuki Hub stopped rebooting by itself. In older versions i didn't have to go near it forever. It just silently restarted in case of crash (?), but not anymore. At least not always as seen on screenshot below.

REQUESTED INFORMATION

Make sure your have performed every step and checked the applicable boxes before submitting your issue. Thank you!

• Read the Contributing Guide and Policy and the Code of Conduct
• Searched the problem in issues
• Searched the problem in discussions
• Searched the problem in the docs
• Searched the problem in the chat
• Device used (e.g., ESP32-S3): ESP32 Dev Kit
• Nuki Hub binary firmware version number used: 9.02
  • Pre-compiled
  • Self-compiled
• Provide the output of http://nukihubIP/info:

System Information
------------ NUKI HUB ------------
Version: 9.02
Build: 11995573722.4.1
Build type: Release
Build date: 2024-11-24
Updater version: 9.02
Updater build: 11995573722.4.1
Updater build date: 2024-11-24
Uptime (min): 0
Config version: 902
Last restart reason FW: NotApplicable
Last restart reason ESP: ESP_RST_POWERON: Reset due to power-on event.
Free internal heap: 61920
Total internal heap: 260580
PSRAM Available: No
Network task stack high watermark: 8652
Nuki task stack high watermark: 5024

------------ GENERAL SETTINGS ------------
Network task stack size: 12288
Nuki task stack size: 8192
Check for updates: No
Latest version: 9.02
Allow update from MQTT: No
Web configurator username: ***
Web configurator password: ***
Web configurator enabled: Yes
Publish debug information enabled: No
MQTT log enabled: Yes
Webserial enabled: No
Bootloop protection enabled: No

------------ NETWORK ------------
Network device: Built-in Wi-Fi
Network connected: Yes
IP Address: 192.168.x.40
SSID: s16net
BSSID of AP: CC:F4:11:xx
ESP32 MAC address: A8:42:E3:xx

------------ NETWORK SETTINGS ------------
Nuki Hub hostname: nukihub
DHCP enabled: Yes
RSSI Publish interval (s): 60
Find WiFi AP with strongest signal: No
Restart ESP32 on network disconnect enabled: Yes
MQTT Timeout until restart (s): 30

------------ MQTT ------------
MQTT connected: Yes
MQTT broker address: 192.168.86.150
MQTT broker port: 1883
MQTT username: ***
MQTT password: ***
MQTT base topic: nuki
MQTT SSL CA: Not set
MQTT SSL CRT: Not set
MQTT SSL Key: Not set

------------ BLUETOOTH ------------
Bluetooth TX power (dB): 9
Bluetooth command nr of retries: 3
Bluetooth command retry delay (ms): 100
Seconds until reboot when no BLE beacons received: 60

------------ QUERY / PUBLISH SETTINGS ------------
Lock/Opener state query interval (s): 1800
Publish Nuki device authorization log: No
Max authorization log entries to retrieve: 5
Battery state query interval (s): 1800
Most non-JSON MQTT topics disabled: No
Publish Nuki device config: Yes
Config query interval (s): 3600
Publish Keypad info: No
Keypad query interval (s): 1800
Enable Keypad control: Yes
Publish Keypad topic per entry: No
Publish Keypad codes: No
Allow checking Keypad codes: No
Max keypad entries to retrieve: 10
Publish timecontrol info: No
Keypad query interval (s): 1800
Enable timecontrol control: No
Publish timecontrol topic per entry: No
Max timecontrol entries to retrieve: 10

------------ HOME ASSISTANT ------------
Home Assistant auto discovery enabled: Yes
Home Assistant auto discovery topic: homeassistant/
Nuki Hub configuration URL for HA: http://192.168.x.40

------------ NUKI LOCK ------------
Lock enabled: Yes
Paired: Yes
Nuki Hub device ID: 4021158070
Nuki device ID: ***
Firmware version: 3.9.5
Hardware version: 2.10
Valid PIN set: No
Has door sensor: No
Has keypad: No
Timecontrol highest entries count: 0
Register as: Bridge

------------ HYBRID MODE ------------
Hybrid mode enabled: No

------------ NUKI LOCK ACL ------------
Lock: Allowed
Unlock: Allowed
Unlatch: Allowed
Lock N Go: Allowed
Lock N Go Unlatch: Allowed
Full Lock: Allowed
Fob Action 1: Allowed
Fob Action 2: Allowed
Fob Action 3: Allowed

------------ NUKI LOCK CONFIG ACL ------------
Name: Disallowed
Latitude: Disallowed
Longitude: Disallowed
Auto Unlatch: Disallowed
Pairing enabled: Allowed
Button enabled: Allowed
LED flash enabled: Allowed
LED brightness: Disallowed
Timezone offset: Disallowed
DST mode: Disallowed
Fob Action 1: Disallowed
Fob Action 2: Disallowed
Fob Action 3: Disallowed
Single Lock: Allowed
Advertising Mode: Disallowed
Timezone ID: Disallowed
Unlocked Position Offset Degrees: Disallowed
Locked Position Offset Degrees: Disallowed
Single Locked Position Offset Degrees: Disallowed
Unlocked To Locked Transition Offset Degrees: Disallowed
Lock n Go timeout: Disallowed
Single button press action: Disallowed
Double button press action: Disallowed
Detached cylinder: Disallowed
Battery type: Disallowed
Automatic battery type detection: Disallowed
Unlatch duration: Disallowed
Auto lock timeout: Disallowed
Auto unlock disabled: Allowed
Nightmode enabled: Disallowed
Nightmode start time: Disallowed
Nightmode end time: Disallowed
Nightmode auto lock enabled: Disallowed
Nightmode auto unlock disabled: Disallowed
Nightmode immediate lock on start: Disallowed
Auto lock enabled: Allowed
Immediate auto lock enabled: Disallowed
Auto update enabled: Disallowed
Reboot Nuki: Disallowed

------------ NUKI OPENER ------------
Opener enabled: Yes
Paired: Yes
Nuki Hub device ID: 4021158070
Nuki device ID: ***
Firmware version: 1.11.0
Hardware version: 4.17
Opener valid PIN set: Yes
Opener has keypad: No
Timecontrol highest entries count: 0
Register as: Bridge
Nuki Opener Lock/Unlock action set to Continuous mode in Home Assistant: No

------------ NUKI OPENER ACL ------------
Activate Ring-to-Open: Allowed
Deactivate Ring-to-Open: Allowed
Electric Strike Actuation: Allowed
Activate Continuous Mode: Allowed
Deactivate Continuous Mode: Allowed
Fob Action 1: Allowed
Fob Action 2: Allowed
Fob Action 3: Allowed

------------ NUKI OPENER CONFIG ACL ------------
Name: Disallowed
Latitude: Disallowed
Longitude: Disallowed
Pairing enabled: Disallowed
Button enabled: Allowed
LED flash enabled: Allowed
Timezone offset: Disallowed
DST mode: Disallowed
Fob Action 1: Disallowed
Fob Action 2: Disallowed
Fob Action 3: Disallowed
Operating Mode: Disallowed
Advertising Mode: Disallowed
Timezone ID: Disallowed
Intercom ID: Disallowed
BUS mode Switch: Disallowed
Short Circuit Duration: Disallowed
Eletric Strike Delay: Allowed
Random Electric Strike Delay: Disallowed
Electric Strike Duration: Allowed
Disable RTO after ring: Disallowed
RTO timeout: Disallowed
Doorbell suppression: Disallowed
Doorbell suppression duration: Disallowed
Sound Ring: Allowed
Sound Open: Disallowed
Sound RTO: Disallowed
Sound CM: Disallowed
Sound confirmation: Disallowed
Sound level: Allowed
Single button press action: Disallowed
Double button press action: Disallowed
Battery type: Disallowed
Automatic battery type detection: Disallowed
Reboot Nuki: Disallowed

------------ GPIO ------------

TO REPRODUCE

Leave running for some time, eventually it dies and won't recover.
The red onboard LED is still on when it "hangs". Manually plugging it out and in boots it up again:

EXPECTED BEHAVIOUR

Reboot automatically if it "hangs", as it was with pre-9 version.

SCREENSHOTS

ADDITIONAL CONTEXT

Some logs when it becomes unavailable. But i don't see any pattern there:

Home Door Nuki Hub restart reason ESP became unavailable
7:42:08 PM
Home Door MQTT Log changed to networkTask is running
7:40:16 PM
Home Door MQTT Log changed to Done querying lock state
7:39:20 PM

(Please, remember to close the issue when the problem has been addressed)

[combine-space]

I also get connection loss with 9.02 after some hours of uptime. I don't know if its because it wont reboot, it's kind of hard to debug. At least I can report that the ring detection works again with this version 🎉.

Device: M5Stack Atom Lite

Info:

System Information
------------ NUKI HUB ------------
Version: 9.02
Build: 11995573722.4.1
Build type: Release
Build date: 2024-11-24
Updater version: 
Updater build: 
Updater build date: 
Uptime (min): 2
Config version: 902
Last restart reason FW: NotApplicable
Last restart reason ESP: ESP_RST_POWERON: Reset due to power-on event.
Free internal heap: 66396
Total internal heap: 260580
PSRAM Available: No
Network task stack high watermark: 8320
Nuki task stack high watermark: 5092

------------ GENERAL SETTINGS ------------
Network task stack size: 12288
Nuki task stack size: 8192
Check for updates: Yes
Latest version: 9.02
Allow update from MQTT: No
Web configurator username: ***
Web configurator password: ***
Web configurator enabled: Yes
Publish debug information enabled: No
MQTT log enabled: Yes
Webserial enabled: No
Bootloop protection enabled: No

------------ NETWORK ------------
Network device: Built-in Wi-Fi
Network connected: Yes
IP Address: 10.0.x.10
SSID: ***
BSSID of AP: ***
ESP32 MAC address: ***

------------ NETWORK SETTINGS ------------
Nuki Hub hostname: nukihub
DHCP enabled: Yes
RSSI Publish interval (s): 60
Find WiFi AP with strongest signal: No
Restart ESP32 on network disconnect enabled: Yes
MQTT Timeout until restart (s): 60

------------ MQTT ------------
MQTT connected: Yes
MQTT broker address: 192.168.x.13
MQTT broker port: 1883
MQTT username: ***
MQTT password: ***
MQTT base topic: nukihub
MQTT SSL CA: Not set
MQTT SSL CRT: Not set
MQTT SSL Key: Not set

------------ BLUETOOTH ------------
Bluetooth TX power (dB): 9
Bluetooth command nr of retries: 3
Bluetooth command retry delay (ms): 100
Seconds until reboot when no BLE beacons received: 60

------------ QUERY / PUBLISH SETTINGS ------------
Lock/Opener state query interval (s): 1800
Publish Nuki device authorization log: No
Max authorization log entries to retrieve: 5
Battery state query interval (s): 1800
Most non-JSON MQTT topics disabled: No
Publish Nuki device config: Yes
Config query interval (s): 300
Publish Keypad info: No
Keypad query interval (s): 1800
Enable Keypad control: Yes
Publish Keypad topic per entry: No
Publish Keypad codes: No
Allow checking Keypad codes: No
Max keypad entries to retrieve: 10
Publish timecontrol info: No
Keypad query interval (s): 1800
Enable timecontrol control: No
Publish timecontrol topic per entry: No
Max timecontrol entries to retrieve: 10

------------ HOME ASSISTANT ------------
Home Assistant auto discovery enabled: Yes
Home Assistant auto discovery topic: homeassistant/
Nuki Hub configuration URL for HA: http://10.0.x.10

------------ NUKI LOCK ------------
Lock enabled: No

------------ NUKI OPENER ------------
Opener enabled: Yes
Paired: Yes
Nuki Hub device ID: 2328545398
Nuki device ID: ***
Firmware version: 1.10.1
Hardware version: 4.17
Opener valid PIN set: Yes
Opener has keypad: Yes
Keypad highest entries count: 0
Timecontrol highest entries count: 0
Register as: Bridge
Nuki Opener Lock/Unlock action set to Continuous mode in Home Assistant: No

------------ NUKI OPENER ACL ------------
Activate Ring-to-Open: Allowed
Deactivate Ring-to-Open: Allowed
Electric Strike Actuation: Allowed
Activate Continuous Mode: Allowed
Deactivate Continuous Mode: Allowed
Fob Action 1: Disallowed
Fob Action 2: Disallowed
Fob Action 3: Disallowed

------------ NUKI OPENER CONFIG ACL ------------
Name: Allowed
Latitude: Allowed
Longitude: Allowed
Pairing enabled: Allowed
Button enabled: Allowed
LED flash enabled: Allowed
Timezone offset: Allowed
DST mode: Allowed
Fob Action 1: Allowed
Fob Action 2: Allowed
Fob Action 3: Allowed
Operating Mode: Allowed
Advertising Mode: Allowed
Timezone ID: Allowed
Intercom ID: Allowed
BUS mode Switch: Allowed
Short Circuit Duration: Allowed
Eletric Strike Delay: Allowed
Random Electric Strike Delay: Allowed
Electric Strike Duration: Allowed
Disable RTO after ring: Allowed
RTO timeout: Allowed
Doorbell suppression: Allowed
Doorbell suppression duration: Allowed
Sound Ring: Allowed
Sound Open: Allowed
Sound RTO: Allowed
Sound CM: Allowed
Sound confirmation: Allowed
Sound level: Allowed
Single button press action: Allowed
Double button press action: Allowed
Battery type: Allowed
Automatic battery type detection: Allowed
Reboot Nuki: Allowed

------------ GPIO ------------

If I can provide more info or do some debugging, just let me know.

[ohadbenita]

Happens to me as well, didn't happen in 9.01 which, for some reason, I can't downgrade to.

[ohadbenita]

PROBLEM DESCRIPTION

Nuki Hub stopped rebooting by itself. In older versions i didn't have to go near it forever. It just silently restarted in case of crash (?), but not anymore. At least not always as seen on screenshot below.

REQUESTED INFORMATION

Make sure your have performed every step and checked the applicable boxes before submitting your issue. Thank you!

• Read the Contributing Guide and Policy and the Code of Conduct

• Searched the problem in issues

• Searched the problem in discussions

• Searched the problem in the docs

• Searched the problem in the chat

• Device used (e.g., ESP32-S3): ESP32 Dev Kit

• Nuki Hub binary firmware version number used: 9.02

  • Pre-compiled
  • Self-compiled

• Provide the output of http://nukihubIP/info:

System Information
------------ NUKI HUB ------------
Version: 9.02
Build: 11995573722.4.1
Build type: Release
Build date: 2024-11-24
Updater version: 9.02
Updater build: 11995573722.4.1
Updater build date: 2024-11-24
Uptime (min): 0
Config version: 902
Last restart reason FW: NotApplicable
Last restart reason ESP: ESP_RST_POWERON: Reset due to power-on event.
Free internal heap: 61920
Total internal heap: 260580
PSRAM Available: No
Network task stack high watermark: 8652
Nuki task stack high watermark: 5024

------------ GENERAL SETTINGS ------------
Network task stack size: 12288
Nuki task stack size: 8192
Check for updates: No
Latest version: 9.02
Allow update from MQTT: No
Web configurator username: ***
Web configurator password: ***
Web configurator enabled: Yes
Publish debug information enabled: No
MQTT log enabled: Yes
Webserial enabled: No
Bootloop protection enabled: No

------------ NETWORK ------------
Network device: Built-in Wi-Fi
Network connected: Yes
IP Address: 192.168.x.40
SSID: s16net
BSSID of AP: CC:F4:11:xx
ESP32 MAC address: A8:42:E3:xx

------------ NETWORK SETTINGS ------------
Nuki Hub hostname: nukihub
DHCP enabled: Yes
RSSI Publish interval (s): 60
Find WiFi AP with strongest signal: No
Restart ESP32 on network disconnect enabled: Yes
MQTT Timeout until restart (s): 30

------------ MQTT ------------
MQTT connected: Yes
MQTT broker address: 192.168.86.150
MQTT broker port: 1883
MQTT username: ***
MQTT password: ***
MQTT base topic: nuki
MQTT SSL CA: Not set
MQTT SSL CRT: Not set
MQTT SSL Key: Not set

------------ BLUETOOTH ------------
Bluetooth TX power (dB): 9
Bluetooth command nr of retries: 3
Bluetooth command retry delay (ms): 100
Seconds until reboot when no BLE beacons received: 60

------------ QUERY / PUBLISH SETTINGS ------------
Lock/Opener state query interval (s): 1800
Publish Nuki device authorization log: No
Max authorization log entries to retrieve: 5
Battery state query interval (s): 1800
Most non-JSON MQTT topics disabled: No
Publish Nuki device config: Yes
Config query interval (s): 3600
Publish Keypad info: No
Keypad query interval (s): 1800
Enable Keypad control: Yes
Publish Keypad topic per entry: No
Publish Keypad codes: No
Allow checking Keypad codes: No
Max keypad entries to retrieve: 10
Publish timecontrol info: No
Keypad query interval (s): 1800
Enable timecontrol control: No
Publish timecontrol topic per entry: No
Max timecontrol entries to retrieve: 10

------------ HOME ASSISTANT ------------
Home Assistant auto discovery enabled: Yes
Home Assistant auto discovery topic: homeassistant/
Nuki Hub configuration URL for HA: http://192.168.x.40

------------ NUKI LOCK ------------
Lock enabled: Yes
Paired: Yes
Nuki Hub device ID: 4021158070
Nuki device ID: ***
Firmware version: 3.9.5
Hardware version: 2.10
Valid PIN set: No
Has door sensor: No
Has keypad: No
Timecontrol highest entries count: 0
Register as: Bridge

------------ HYBRID MODE ------------
Hybrid mode enabled: No

------------ NUKI LOCK ACL ------------
Lock: Allowed
Unlock: Allowed
Unlatch: Allowed
Lock N Go: Allowed
Lock N Go Unlatch: Allowed
Full Lock: Allowed
Fob Action 1: Allowed
Fob Action 2: Allowed
Fob Action 3: Allowed

------------ NUKI LOCK CONFIG ACL ------------
Name: Disallowed
Latitude: Disallowed
Longitude: Disallowed
Auto Unlatch: Disallowed
Pairing enabled: Allowed
Button enabled: Allowed
LED flash enabled: Allowed
LED brightness: Disallowed
Timezone offset: Disallowed
DST mode: Disallowed
Fob Action 1: Disallowed
Fob Action 2: Disallowed
Fob Action 3: Disallowed
Single Lock: Allowed
Advertising Mode: Disallowed
Timezone ID: Disallowed
Unlocked Position Offset Degrees: Disallowed
Locked Position Offset Degrees: Disallowed
Single Locked Position Offset Degrees: Disallowed
Unlocked To Locked Transition Offset Degrees: Disallowed
Lock n Go timeout: Disallowed
Single button press action: Disallowed
Double button press action: Disallowed
Detached cylinder: Disallowed
Battery type: Disallowed
Automatic battery type detection: Disallowed
Unlatch duration: Disallowed
Auto lock timeout: Disallowed
Auto unlock disabled: Allowed
Nightmode enabled: Disallowed
Nightmode start time: Disallowed
Nightmode end time: Disallowed
Nightmode auto lock enabled: Disallowed
Nightmode auto unlock disabled: Disallowed
Nightmode immediate lock on start: Disallowed
Auto lock enabled: Allowed
Immediate auto lock enabled: Disallowed
Auto update enabled: Disallowed
Reboot Nuki: Disallowed

------------ NUKI OPENER ------------
Opener enabled: Yes
Paired: Yes
Nuki Hub device ID: 4021158070
Nuki device ID: ***
Firmware version: 1.11.0
Hardware version: 4.17
Opener valid PIN set: Yes
Opener has keypad: No
Timecontrol highest entries count: 0
Register as: Bridge
Nuki Opener Lock/Unlock action set to Continuous mode in Home Assistant: No

------------ NUKI OPENER ACL ------------
Activate Ring-to-Open: Allowed
Deactivate Ring-to-Open: Allowed
Electric Strike Actuation: Allowed
Activate Continuous Mode: Allowed
Deactivate Continuous Mode: Allowed
Fob Action 1: Allowed
Fob Action 2: Allowed
Fob Action 3: Allowed

------------ NUKI OPENER CONFIG ACL ------------
Name: Disallowed
Latitude: Disallowed
Longitude: Disallowed
Pairing enabled: Disallowed
Button enabled: Allowed
LED flash enabled: Allowed
Timezone offset: Disallowed
DST mode: Disallowed
Fob Action 1: Disallowed
Fob Action 2: Disallowed
Fob Action 3: Disallowed
Operating Mode: Disallowed
Advertising Mode: Disallowed
Timezone ID: Disallowed
Intercom ID: Disallowed
BUS mode Switch: Disallowed
Short Circuit Duration: Disallowed
Eletric Strike Delay: Allowed
Random Electric Strike Delay: Disallowed
Electric Strike Duration: Allowed
Disable RTO after ring: Disallowed
RTO timeout: Disallowed
Doorbell suppression: Disallowed
Doorbell suppression duration: Disallowed
Sound Ring: Allowed
Sound Open: Disallowed
Sound RTO: Disallowed
Sound CM: Disallowed
Sound confirmation: Disallowed
Sound level: Allowed
Single button press action: Disallowed
Double button press action: Disallowed
Battery type: Disallowed
Automatic battery type detection: Disallowed
Reboot Nuki: Disallowed

------------ GPIO ------------

TO REPRODUCE

Leave running for some time, eventually it dies and won't recover. The red onboard LED is still on when it "hangs". Manually plugging it out and in boots it up again:

EXPECTED BEHAVIOUR

Reboot automatically if it "hangs", as it was with pre-9 version.

SCREENSHOTS

ADDITIONAL CONTEXT

Some logs when it becomes unavailable. But i don't see any pattern there:

Home Door Nuki Hub restart reason ESP became unavailable
7:42:08 PM
Home Door MQTT Log changed to networkTask is running
7:40:16 PM
Home Door MQTT Log changed to Done querying lock state
7:39:20 PM

(Please, remember to close the issue when the problem has been addressed)

In my case I was able to connect to the lock, but it dropped the MQTT connection to home assistant.
Restarting the Nuki hub from the web interface regained the MQTT connection between the Nuki hub and HA.

[combine-space]

I gathered the serial logs. In my case as soon the nuki hub gets unresponsive, logging also stops (it returns some empty lines before it dies). I can't see any hints that a problem was detected prior to the connection loss.

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 188777542, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:4560
load:0x40078000,len:15336
load:0x40080400,len:4
ho 8 tail 4 room 4
load:0x40080404,len:3176
entry 0x400805b8
Partition size: 2555904
Partition subtype: 16
Nuki Hub version 9.02
Nuki Hub build 11995573722.4.1
Load GPIO configuration
IP configuration: DHCP
Hardware detect: 1
MQTT without TLS.
Network device: Built-in Wi-Fi
Attempting to connect to saved SSID [REDACTED]
Wi-Fi async scan started
Host name: nukihub
MQTT Broker: 192.168.X.13:1883
Nuki Lock disabled
Nuki Opener enabled
Device id opener: 2328545398
Opener state interval: 1800 | Battery interval: 1800 | Publish auth data: no
Wi-Fi scan done
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
SSID [REDACTED]
WiFi disconnected
Retrying
Wi-Fi connected
IP: 10.0.X.10
Attempting MQTT connection
MQTT: Connecting with user: nukihub
MQTT connected
HASS setup for NukiHub completed.
Subscribing to MQTT topic: nukihub/opener/action
Subscribing to MQTT topic: nukihub/opener/configuration/action
Subscribing to MQTT topic: nukihub/opener/query/config
Subscribing to MQTT topic: nukihub/opener/query/lockstate
Subscribing to MQTT topic: nukihub/opener/query/battery
Subscribing to MQTT topic: nukihub/opener/keypad/command/action
Subscribing to MQTT topic: nukihub/opener/keypad/command/id
Subscribing to MQTT topic: nukihub/opener/keypad/command/name
Subscribing to MQTT topic: nukihub/opener/keypad/command/code
Subscribing to MQTT topic: nukihub/opener/keypad/command/enabled
Subscribing to MQTT topic: nukihub/opener/query/keypad
Subscribing to MQTT topic: nukihub/opener/keypad/actionJson
Subscribing to MQTT topic: nukihub/maintenance/reset
Subscribing to MQTT topic: nukihub/maintenance/webserver/enable
Nuki opener start pairing
Nuki opener paired
Result (attempt 1): MQTT recently connected, ignoring opener action.
MQTT recently connected, ignoring opener action.
locked
Done querying opener state
Querying opener battery state: success
Done querying opener battery state
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config
HASS setup for opener completed.
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid

[TRUNCATED repeating messages]

networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Attempting MQTT connection
Nuki opener
Attempting MQTT connection
Nuki opener PIN is invalid
MQTT: Connectingconfig result: error
Opener advanced config result: error
Invalid/Unexpected opener advanced config received, Advanced config is not valid
Invalid/Unexpected opener config and/or advanced config received, retrying in 10 seconds
MQTT disconnected. Reason: TCP_DISCONNECTED
MQTT connect failednetworkTask is running
Attempting MQTT connection
MQTT: Connecting with user: nukihub
MQTT connected
Subscribing to MQTT topic: nukihub/opener/action
Subscribing to MQTT topic: nukihub/opener/configuration/action
Subscribing to MQTT topic: nukihub/opener/query/config
Subscribing to MQTT topic: nukihub/opener/query/lockstate
Subscribing to MQTT topic: nukihub/opener/query/battery
Subscribing to MQTT topic: nukihub/opener/keypad/command/action
Subscribing to MQTT topic: nukihub/opener/keypad/command/id
Subscribing to MQTT topic: nukihub/opener/keypad/command/name
Subscribing to MQTT topic: nukihub/opener/keypad/command/code
Subscribing to MQTT topic: nukihub/opener/keypad/command/enabled
Subscribing to MQTT topic: nukihub/opener/query/keypad
Subscribing to MQTT topic: nukihub/opener/keypad/actionJson
Subscribing to MQTT topic: nukihub/maintenance/reset
Subscribing to MQTT topic: nukihub/maintenance/webserver/enable
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config
MQTT recently connected, ignoring opener action.
nukiTask is running
networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config

[TRUNCATED repeating messages]

networkTask is running
nukiTask is running
networkTask is running
nukiTask is running
Opener config result: success(1)
Nuki opener PIN is set
Nuki opener PIN is valid
Opener advanced config result: success
Done retrieving opener config and advanced config
networkTask is running
nukiTask is running





























EOF