Performance issues with bridging gpu_lidar data

[roni-kreinin]

Environment

• OS Version: Ubuntu 22.04
• ROS 2 Humble
• Ignition Fortress
• Source or binary build?
  Binary: 0.244.9

Description

The Create 3 sim uses a number of gpu_lidar sensors to simulate the IR intensity sensors as well as cliff detection sensors. The sensor data is bridged to ROS 2 with ros_gz_bridge and used by nodes. Performance of the simulation is reduced significantly as soon as the bridges for these sensors are added, and the topic frequency in ros2 is well below the desired update_rate specified in the urdf.

• Expected behavior: LaserScan messages should be published at the set update_rate of the sensor.
• Actual behavior: ros2 topic hz reports that topics are published at around 60% of the update rate. Additionally, the RTF in Gazebo drops significantly when the parameter_bridge nodes for the lidars are running.

Steps to reproduce

1. Build create3_sim from source.
2. ros2 launch irobot_create_ignition_bringup create_ignition.launch.py
3. Check scan topic frequencies:
   ros2 topic hz /_internal/cliff_front_left/scan
ros2 topic hz /_internal/ir_intensity_front_center_left/scan

For me the cliff sensors publish at around 47hz and the ir sensors at around 35hz. They both have update rates set to 62hz.
RTF also jumps between 40-60%.

4. Disable the ir and cliff sensor bridges by commenting out lines 196 and 197 in create3_ros_ignition_bridge.launch.py. Launch the sim again.

With the bridges disabled I now have a steady RTF of around 90%.

5. Re-enable the sensor bridges and uncap update_rate by commenting out line 58 in common_properties.urdf.xacro. Launch the sim again.

With this configuration, my RTF sits at a very consistent 31-33% without much fluctuation. Additionally, both cliff and IR sensors report around 160hz on their respective ros2 topics.

To achieve the desired 62hz, I have to set the update rate of the sensors to around 100hz. Clearly my machine is capable of publishing 160hz, so I am not sure what is causing this loss of ~1/3 the desired frequency. Additionally, why does the ros_gz_bridge cause such significantly reduced Gazebo RTF performance?

[roni-kreinin]

@azeey Do you have any insight into this issue?

[azeey]

Without delving too deeply, I noticed that the launch file is creating one bridge node for all cliff sensors and one node for ir sensors. To improve performance, I recommend creating a node for each topic/sensor.

[roni-kreinin]

@azeey I created separate nodes for each topic and sensor like this:

ir_bridges = GroupAction([
        Node(package='ros_gz_bridge', executable='parameter_bridge',
            name=ir + '_bridge',
            output='screen',
            parameters=[{
                'use_sim_time': use_sim_time
            }],
            arguments=[
                ['/world/', LaunchConfiguration('world'),
                '/model/', LaunchConfiguration('robot_name'),
                '/link/' + ir + '/sensor/' + ir + '/scan' +
                '@sensor_msgs/msg/LaserScan[ignition.msgs.LaserScan']
            ],
            remappings=[
                (['/world/', LaunchConfiguration('world'),
                    '/model/', LaunchConfiguration('robot_name'),
                    '/link/' + ir + '/sensor/' + ir + '/scan'],
                '_internal/' + ir + '/scan')
            ]) for ir in ir_intensity_sensors
    ])

Still seeing the same performance though. I also tested using the point cloud data instead of laserscans but it performed the same.

[roni-kreinin]

From further investigation it seems that anything that subscribes to the /scan topics in ignition will cause a significant drop in performance. Do the sensors only publish topics when there is a subscriber?

[azeey]

Do the sensors only publish topics when there is a subscriber?

Yes, I believe so. So you might just be running into a compute limitation with your system. Are you using an NVIDIA GPU and is it configured properly?

[roni-kreinin]

I am using a GTX 1650 and it is barely reaching 30% usage. My CPU is also only reaching around 40% utilisation.
Are there configurations I need to make specifically for gazebo?

Also as a separate question: is there a reason why ogre2 performs much worse than ogre as the render engine for sensors?

[roni-kreinin]

There seems to be some sort of overhead in the gz-transport subscriber that prevents it from achieving the full update rate that is requested.

For example, if I replace the Subscribe line here with:

ignition::transport::SubscribeOptions opts;
opts.SetMsgsPerSec(30u);
node->Subscribe(topic_name, subCb, opts);

I would expect it to cap at 30 hz, since it was publishing at over 30hz uncapped before. But instead, I am seeing closer to 20 hz on the ros topic. The update rate on the sensor hasn't actually changed from 62hz.

[zp-yang]

I think we are having the same problem see gz-sensors #332. I believe gpulidar, ir, and camera are all rendering sensors.