8311_fix_vlans=1
8311_internet_vlan=0
8311_services_vlan=36
8311_ipaddr=192.168.11.1
8311_netmask=255.255.255.0
8311_gateway=192.168.11.254
8311_ping_ip=192.168.11.2
8311_console_en=1
8311_ethtool_speed=speed 2500 autoneg off duplex full
8311_failsafe_delay=30
8311_persist_root=0
8311_root_pwhash=$1$BghTQV7M$ZhWWiCgQptC1hpUdIfa0e.
8311_rx_los=0
8311_cp_hw_ver_sync=1
8311_device_sn=DM222XXXXXXXXXX
8311_equipment_id=5690
8311_gpon_sn=SMBSXXXXXXXX
8311_hw_ver=Fast5689EBell
8311_mib_file=/etc/mibs/prx300_1V.ini
8311_reg_id_hex=00
8311_sw_verA=SGC830007C
8311_sw_verB=SGC830006E
8311_vendor_id=SMBS
8311_fix_vlans - Fix VLANs
Set to 0 to disable the automatic fixes that are applied to VLANs.
8311_internet_vlan - Internet VLAN
Set the local VLAN ID to use for the Internet or 0 to make the Internet untagged (and also remove VLAN 0) (0 to 4095). Defaults to 0 (untagged).
8311_services_vlan - Services VLAN
Set the local VLAN ID to use for Services (ie TV/Home Phone) (1 to 4095). This fixes multi-service on Bell.
8311_ipaddr - IP Address
Set the management IP address. Defaults to 192.168.11.1
8311_netmask - Subnet Mask
Set the management subnet mask. Defaults to 255.255.255.0
8311_gateway - Gateway
Set the management gateway. Defaults to the IP address (ie. no default gateway)
8311_ping_ip - Ping IP
Sets an IP address to ping every 5 seconds, this can helps with reaching the stick. Defaults to the 2nd ip address in the configured management network (ie. 192.168.11.2).
8311_console_en - Serial console
Set to 1 to enable the serial console, this will cause TX_FAULT to be asserted as it shares the same SFP pin.
8311_ethtool_speed - Ethtool Speed Settings
Set ethtool speed settings on the eth0_0 interface (ethtool -s).
8311_factory_mode - Factory Mode
Set to 1 to enable factory mode, otherwise factory mode will be automatically disabled on boot.
8311_failsafe_delay - Failsafe Delay
Sets the number of seconds that we will delay the startup of omcid for at bootup (30 to 300). Defaults to 30 seconds.
8311_lct_mac - LCT MAC Address
Set the MAC address on the LCT management interface.
8311_persist_root - Persist RootFS
Set to 1 to allow the root file system to stay persistent (would also require that you modify the bootcmd fwenv). This is not recommended and should only be used for debug/testing purposes.
8311_root_pwhash - Root password hash
Allows you to set a custom root password by setting the hash.
8311_rx_los - RX_LOS Workaround
Set to 0 to monitor the status of the RX_LOS pin to disable it any time it gets enabled. This will allow the stick to be accessible in devices which disable access to the port if RX_LOS is being asserted.
8311_cp_hw_ver_sync - Sync Circuit Pack Version
When set to 1 and 8311_hw_ver is also set, will modify the configured mib file to set the Version field of any Circuit Pack MEs to match the Hardware version.
8311_device_sn - Device Serial Number
Sets the physical device S/N, this is more or less display only.
8311_equipment_id - Equipment ID
Sets the PON Equipment ID field in the ONU2-G ME (257).
8311_gpon_sn - GPON Serial Number / ONT ID
Sets the GPON Serial Number sent to the OLT in various MEs (4 letters, followed by 8 hex digits).
8311_hw_ver - Hardware Version
Set the Hardware version string sent to the OLT in various MEs (up to 14 characters).
8311_iphost_domain - IP Host Domain Name
Set the domain name sent to the OLT in ME 134 (up to 25 characters).
8311_iphost_hostname - IP Host Hostname
Set the hostname sent to the OLT in ME 134 (up to 25 characters).
8311_iphost_mac - IP Host MAC Address
Set the MAC address sent to the OLT in ME 134.
8311_loid - Logical ONU ID
Sets the Logical ONU ID presented to the OLT in ME 256 (up to 24 characters).
8311_lpwd - Logical Password
Sets the Logical Password prsented to the OLT in ME 256 (up to 12 characters).
8311_mib_file - MIB File
Sets the MIB file used by omcid. Defaults to /etc/mibs/prx300_1U.ini
8311_pon_slot - PON Slot
Sets the slot number that the UNI port is presented on, needed on some ISPs.
8311_reg_id_hex - Registration ID
Sets the Registration ID (up to 36 characters [72 hex]) sent to the OLT in hex format. This is where you would set a ploam password (which is contained in the last 12 characters).
8311_sw_verA / 8311_sw_verB - Software Versions
Sets the image specific software versions sent in the Software image MEs (7).
8311_vendor_id - Vendor ID
Sets the PON Vendor ID sent to the OLT, automatically derived from the GPON Serial Number if not set (4 letters).
SSH host keys (all of /etc/dropbear) and authorized_keys (all of /root/.ssh) are now stored persistently.
Previous UCI settings will be automatically migrated.
The current root password (change with passwd) can be persisted using the 8311-persist-root-password.sh command
Tool for building new modded WAS-110 firmware images
Usage: ./build.sh [options]
Options:
-i --image <filename> Specify stock local upgrade image file.
-I --image-dir <dir> Specify stock image directory (must contain bootcore.bin, kernel.bin, and rootfs.img).
-o --image-out <filename> Specify local upgrade image to output.
-h --help This help text
Tool for creating new WAS-110 local upgrade images
Usage: ./create.sh [options]
Options:
-i --image <filename> Specify local upgrade image file to create (required).
-H --header <filename> Specify filename of image header to base image off of (default: header.bin).
-b --bootcore <filename> Specify filename of bootcore image to place in created image (default: bootcore.bin).
-k --kernel <filename> Specify filename of kernel image to place in created image (default: kernel.bin).
-r --rootfs <filename> Specify filename of rootfs image to place in created image (default: rootfs.img).
-V --image-version <version> Specify version string to set on created image (14 characters max).
-h --help This help text
Tool for extracting stock WAS-110 local upgrade images
Usage: ./extract.sh [options]
Options:
-i --image <filename> Specify local upgrade image file to extract (required).
-H --header <filename> Specify filename to extract image header to (default: header.bin).
-b --bootcore <filename> Specify filename to extract bootcore image to (default: bootcore.bin).
-k --kernel <filename> Specify filename to extract kernel image to (default: kernel.bin).
-r --rootfs <filename> Specify filename to extract rootfs image to (default: rootfs.img).
-h --help This help text